Finite Element Analysis of Crane Hook and Optimization Using Taguchi Approach

Authors

  • Omkar P. Bhatkar Assistance Professors, Mechanical Engineering, Rajendra Mane College of Engineering and Technology, Ambav, Devrukh, Ratnagiri -415612, Mumbai University, Maharashtra, India
  • Arun V. Javir Assistance Professors, Mechanical Engineering, Rajendra Mane College of Engineering and Technology, Ambav, Devrukh, Ratnagiri -415612, Mumbai University, Maharashtra, India
  • Shinde Ajay Ashok Student, Mechanical Engineering, Rajendra Mane College of Engineering and Technology, Ambav, Devrukh, Ratnagiri -415612, Mumbai University, Maharashtra, India
  • Sawant Subodh Sumant Student, Mechanical Engineering, Rajendra Mane College of Engineering and Technology, Ambav, Devrukh, Ratnagiri -415612, Mumbai University, Maharashtra, India
  • Ukarde Suraj Eknath Student, Mechanical Engineering, Rajendra Mane College of Engineering and Technology, Ambav, Devrukh, Ratnagiri -415612, Mumbai University, Maharashtra, India
  • Kavathankar Kunal Shivram Student, Mechanical Engineering, Rajendra Mane College of Engineering and Technology, Ambav, Devrukh, Ratnagiri -415612, Mumbai University, Maharashtra, India

DOI:

https://doi.org/10.53555/nneee.v2i3.217

Keywords:

Trapazoidal section, Taguchi Analysis, Von-misses, stress, FEM(Finite Eiement Method)

Abstract

A Crane hook is a device for grabbing and lifting loads of heavy duty by mean of a device such as crane hoist. A crane hook is usually equipped with a safety latch to prevent the disengagement of the lifting rope to which the load is being attach. The CAD model of a lifting crane hook is initially prepared from the Analytical Design. In the present report crane hook of trapezoidal section is modeled using UG-NX 8.0, further, importing the CAD model into ANSYS 15.0 we estimate until 20 tones i.e. equivalent to 200000N load to be gradually applied, eventually we observed the von-misses stress developed in the model by FEM method these results vonmisses stresses are being compared with Taguchi L9 orthogonal array for specific results. Thus, these results would lead us to determine various stresses and deflections in the designed CAD model. In order to reach the most optimum model from different materials of hook would be tested and the most efficient material would be selected.

References

Santosh Sahu, Ritesh Dewangan, Manas Patnaik, Narendra Yadav, “Study of Crane Hook Having Trapezoidal Section by Finite Element Method & Design of Experiments.” International Journal of Modern Engineering Research (IJMER) www.ijmer.com Vol.2, 2779-2781, Issue.4, JulyAug 2012.

Govind Narayan Sahu, NarendraYadav, “Design and Stress Analysis of various cross section of Hook.” International Journal of Modern Engineering Research (IJMER) Vol. 3, 2249-6645 Issue. 4, Jul - Aug. 2013.

Mr. A. Gopichand, Ms. R. V. S. Lakshmi, Mr. B. Maheshkrishna, “Optimization Of Design Parameters For Crane Hook Using Taguchi Method”, International Journal of Innovative Research in Science, Engineering and Technology (An ISO 3297: 2007 Certified

Organization)Vol. 2, 2319-8753, Issue 12, December 2013.

Mr. A. Gopichand, Ms. R.V.S.Lakshmi, Mr. B. Maheshkrishna, “Optimization Of Design Parameters For Crane Hook Using Taguchi Method”, International Journal of Innovative Research in Science, Engineering and Technology (An ISO 3297: 2007 Certified

Organization)Vol. 2, ISSN: 2319-8753, Issue 12, December 2013.

Ajeet Bergaley, Anshuman Purohit “Structural Analysis of Crane Hook Using Finite ElementMethod”, International Journal of Science and Modern Engineering (IJISME) ISSN: 2319-6386, Volume-1, Issue-10, September 2013.

Patel Paresh and NiravKamdar, “Design and Analysis of Major Component of 120 Tones Capacity of EOT Crane” 2014 IJEDR, Volume 2, Issue 2, ISSN: 2321-9939; 2014.

T. Muromaki, K. Hanahara, Y. Tada, S. Kuroda and T. Fukui “Estimating load condition having caused structure failure and an optimal design taking account of the estimated result” 5th International Conference on Reliable Engineering, 387-406, 2012.

Narvydas E., Puodziuniene N., Circumferential stress concentration factors at the asymmetric shallow notches of the lifting hooks of trapezoidal cross-section. Mechanika, Volume 18(2): 152-157, 2012. .

S. Vinodh, R. Ravikumar,,"Application of probabilistic finite element analysis for crane hook design", Journal of Engineering, Design and Technology, Vol. 10, 255 –275, 2012

M. Shaban, M. I. Mohamed, A. E. Abuelezz, T. Khalifa, “Determination of Stress Distribution in Crane Hook by Caustic”, International

Journal of Innovative Research in Science, Engineering and Technology ISSN: 2319-8753 Vol. 2, 1834-1840 Issue 5, May 2013.

M S. Phadke ‘Quality engineering using robust design’, Pearson Education India Limited, Edition 2006.

R. Uddanwadiker, "Stress Analysis of Crane Hook and Validation by Photo Elasticity," Engineering, Vol. 3 No. 9, 935-941, 2011

Published

2015-03-31

How to Cite

Bhatkar, O. P., Javir, A. V. ., Ashok, S. A. ., Sumant, S. S. ., Eknath, U. S., & Shivram, K. K. . (2015). Finite Element Analysis of Crane Hook and Optimization Using Taguchi Approach. Journal of Advance Research in Electrical & Electronics Engineering (ISSN 2208-2395), 2(3), 27-32. https://doi.org/10.53555/nneee.v2i3.217